Join our mailing list!



Welcome.



Lipo to USB Power Converter
Our Price: $6.95
In Stock
DJI Naza-M Lite with GPS
Our Price: $169.00
(Out of Stock)
This USB power converter will allow you to plug in any 2S to 4S lipo battery and outputs power to a female USB connector. This can be used to charge any USB device like your cell phone of GoPro camera.
For entry-level enthusiasts, DJI now brings out the most cost-effective solution, the NAZA-M Lite flight control system. As the simplified version of NAZA-M, it inherits the high reliability and stability of NAZA-M.
Years in the making, and built from the ground up with simplicity in mind, the Vector has everything we hobbyists have dreamed about for our recreational FPV models, in one small, lightweight easy to use product.
GT Power Wattmeter
Our Price: $33.95
In Stock
GemFan produces some of the finest propellers for Multi-Rotor use.  These standard props are made from ABS plastic with a glass fiber fill for extra strength and durability. Years in the making, and built from the ground up with simplicity in mind, the Vector has everything we hobbyists have dreamed about for our recreational FPV models, in one small, lightweight easy to use product. Everyone that flies electric should have a wattmeter so you can measure exactly how your power system is performing and to make sure you are keeping everything below the max ratings. This wattmeter will measure from 4.8v to 60v and up to 130A.
CC3D Flight Controller with Case
CC3D Flight Controller with Case
Our Price: $21.95
In Stock
This version of CC3D board has two additional ports - one for JR/Spektrum DSM satellite receivers and one for Futaba S.Bus receivers. It includes the CC3D board in a case with a RC cable for standard PWM receivers and a USB cable for firmware upgrades and setup. The hard case can be easily removed if desired. The CC3D comes to you pre-loaded with the OpenPilot firmware but it can also be flashed with CleanFlight firmware if desired. Setup and configuration is then accomplished using the OpenPilot GCS or CleanFlight for Google Chrome.

Please note there is no manual included in the package. Click HERE for the OpenPilot documentation. Click HERE for the CleanFlight Configurator.

The CC3D has been designed from the ground up to perform the following functions:
  • a MultiRotor controller with auto-level, including TriCopters, QuadCopters and HexaCopters
  • a Flybarless Helicopter controller with auto-level
  • a Fixed Wing UAV controller

CC3D controller features:

  • Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM
  • 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer
  • Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.
  • Software support for Windows, Mac and Linux
  • Direct high speed USB support with no drivers required, a truly plug and play device.
  • Spektrum satellite receiver support
  • Futaba S-BUS hardware support
  • Innovative Flexi-port technology for superior port flexibility
  • 4Mbits on-board EEPROM for configuration storage

Flexiport

CopterControl also offers the innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs.

Superior user experience
OpenPilot has tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe.

The OpenPilot project, whist still young, it trying to make Open Source much more user friendly. OpenPilot software is designed to be used by everybody! All major operating systems are supported and install packages are provided. The software is all Free software under the GPLv3 license and not only are you welcome to hack it, but we encourage it!


Sensors and Components:

3-axis Gyroscope array and 3-axis Accelerometer: MPU-6000
Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, DSMJ, DSMX satellites, and Futaba S.Bus receivers
Simultaneous support for multiple receivers
ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels
MainPort functions (configurable): serial telemetry (default), GPS, S.Bus, Spektrum/JR satellites
FlexiPort (configurable): serial telemetry, GPS, Spektrum/JR satellites, or I2C peripherals (under development)
10 PWM outputs to servos or ESC’s, or for camera stabilization
Camera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers
Onboard USB connectivity for easy configuration
USB and serial telemetry and configuration (including wireless with optional radio modules)
Supported by powerful OpenPilot GCS
4 Mbit onboard memory
3C Quaternion based complementary filter running at 500Hz
This Battery Meter and Low-Voltage Alarm is a dual purpose device that works well on aircraft, helicopters and multi-rotor models alike. It's an 8-cell battery meter that will read the total pack voltage, as well as give you the individual cell voltages. It will also sound an alarm at the voltage point you set.
No longer do you need to wonder about your flight pack condition with this compact, low battery voltage alarm. Our Battery Buzzer warns you when you are getting close to the end of your flight and it is time to land.
Naze32 Acro Flight Controller FLYSIGHT 5.8 GHZ SPEXMAN ONE DUAL DIVERSITY FPV GOGGLES WITH PICTURE IN PICTURE
Naze32 Acro Flight Controller
Our Price: $29.95
In Stock
Know your packs! The EOS SENTRY is a quick, convenient, easy-to-use device. It shows at a glance the remaining capacity in your battery pack, cell balance, and other information you need to get the best performance and reliability from your batteries.
At the heart of the Naze32 is a 32bit ST micro work horse of a processor, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration.
Introducing the world's first Picture In Picture FlySight 5.8ghz Dual Diversity video goggles for FPV. Featuring High Resolution (854 x 480) and 30 degree wide field of view.

MinimOSD V1.2 with KV Team Mod
Imax X180 DC Color Touchscreen Charger
Our Price: $79.95
In Stock
MinimOSD V1.2 with KV Team Mod
Our Price: $14.95
In Stock
The iMaxRC X180 DC Touchscreen battery charger is a revolutionary new charger design offering the ultimate in ease of use and modern styling.
This Board can be used just as a normal OSD for APM or it can be used with your MultiWii, Naze32, or CC3D flight controllers. It comes loaded with MW OSD firmware version 1.2 but can be flashed to other firmwares if desired.
GemFan produces some of the finest propellers for Multi-Rotor use.  These standard props are made from ABS plastic with a glass fiber fill for extra strength and durability.
HoverThings Flip 360 FPV ARF Kit
Our Price: $329.95
In Stock
The iMaxRC X150 AC/DC Touchscreen battery charger is a revolutionary new charger design offering the ultimate in ease of use and modern styling.
The new FLIP 360 is designed to be an extremely portable FPV machine. It is small and light, yet will accept 28mm motors and 8" props for aggressive flying. This ARF version includes the frame, motors, ESCs, props, bullet connectors, and power distribution board.
CNC Multifunctional Aluminum Alloy Soldering Fixture. The bullet connector section is made of a high heat durable thermal insulation material. Works with Mini T-plug / T-plug / XT60-plug / XT90-plug / and connectors with 2.0-10.4mm banana-plug/bullet connectors.
Black Pearl RC801 7" Monitor with built in battery and 5.8 Ghz Dual Diversity
DJI Naza-M V2 with GPS
Our Price: $299.00
In Stock
The most popular multi-rotor flight controller just got even better. The DJI Naza-M V2 includes many new features. This set includes a complete system with flight controller, GPS, power management module, LED module, and all needed cables.
Black Pearl RC801 7" Monitor with built in battery and 5.8 Ghz Dual Diversity 32 Channel Receiver, 12V Charger, Sun Shade, standard rubber duck antennas, and several cables.
The Guardian 2D/3D Stabilizer is a must-have product for your model. The Guardian smoothes out air turbulence, but does much more. Unlike cheap gyro stabilizers, it provides true wing leveling capability to help recover from lost orientation!
GemFan produces some of the finest propellers for Multi-Rotor use.  These standard props are made from ABS plastic with a glass fiber fill for extra strength and durability. GemFan produces some of the finest propellers for Multi-Rotor use.  These standard props are made from ABS plastic with a glass fiber fill for extra strength and durability.


Sign Up For Our Newsletter