Found 12 product(s) for Accessories:Dionysus (1-12 of 12)

Accessories:Dionysus
	Dionysus Camera Controller The Camera Position Controller is designed to smoothly move a servo that is used for positioning a camera on the model. The Camera Position Controller works perfectly with a 3 position transmitter switch, or an extra transmitter stick. When the stick or switch is in the center position, the servo does not move. When the stick or switch is moved to one side or another, the servo will slowly move to that position. In Stock - Price: $9.99		Dionysus Dual adjustable servo rate reducer This Dual Adjustable Servo Rate Reducer has the ability to indepenantly slow down two servos. A small potentiometer (POT) allows the servo end to end speed to be adjusted from less than 1 second to 5 seconds. The POT also allows selection of the failsafe signal. In Stock - Price: $21.99
	Dionysus Dual camera controller The Dual Camera Position Controller is designed to smoothly move two servos that are used for positioning a camera on the model. The Camera Position Controller works perfectly with a 3 position transmitter switch, or an extra transmitter stick. When the stick or switch is in the center position, the servo does not move. When the stick or switch is moved to one side or another, the servo will slowly move to that position. In Stock - Price: $21.99		Dionysus Dual Servo Expo The Dionysus Design Dual Expo allows an exponential curve to be applied to the servo signal. The amount of exponent curve is defined by the adjustable potentiometer (POT) on the Dual Expo. Turning the POT to the left decreases the servo sensitivity at the center of it's range. Turning the POT to the right increases the servo sensitivity at the center of it's range. In Stock - Price: $21.99
	Dionysus Glitch reducer The Glitch Reducer will eliminate most glitches before they get to the servos or electronic speed controllers. It will constantly output the last known 'good' signal from the receiver. It will suppress any input signal outside of the signal range. It will also suppress the random input signals that are within the signal range. In Stock - Price: $9.99		Dionysus Revo Mixer The Dionysus Design mixer is designed to perform the revo mixing necessary to fly a helicopter so a standard 4 channel transmitter and any ESCs could be used. In Stock - Price: $21.99
	Dionysus Servo Rate Reducer The Servo Rate Reducer will limit the rate of change for a servo signal. This will slow the servo down for use with retractable landing gear or airplane flaps. The rate at which the servo moves is usually about 3 to 4 seconds end-to-end. In Stock - Price: $9.99		Dionysus Servo rate reducer (extra slow) This Extra Slow Servo Rate Reducer is exactly the same as the standard Servo Rate Reducer, but it's speed has been decreased so the servo movement will take almost 6 seconds end to end. For more information, please see the standard Servo Rate Reducer. In Stock - Price: $9.99
	Dionysus Servo Reverser The Dionysus Design Servo Reverser is designed to reverse the direction of the servo. Most radios include this functionality already, but this Servo Reverser can be used on one side of a Y cable that connects two servos together. In this configuration, only one servo is reversed. This Servo Reverser is also very helpful if one of the servos in a V tail needs to be reversed. The Servo Reverser utilizes a microcontroller that reads in the servo signal from the receiver, and reverses the signal around 1.5ms (the typical signal length of a centered servo). In Stock - Price: $9.99		Dionysus Servo Stretcher The Dionysus Design Servo Stretcher will take the normal 90 degree servo signal from the receiver and stretch it out so the servo actually moves 180 degrees. Most servos can go up to 180 degrees, however the transmitter limits the range to about 90 degrees. This servo stretcher will double the signal range. Out of Stock - Price: $9.99
	Dionysus V-Tail Mixer The Dionysus Design VTail Mixer allows aircraft with a V shaped tail to be controlled with a standard transmitter. The microcontroller inside the V tail mixer mixes the elevator and rudder channels together for the left and right outputs for the V tail. The VTail Mixer also includes a fail-safe mechanism that centers the servos if the input signal is lost. In Stock - Price: $19.99		Dionysus Voltage Isolator This Voltage Isolator is designed to allow your model to use higher voltages only on certain servos. Using higher voltage on the servos will increase the power and reaction time. However, there are other electronics that should not be powered by 6 volts. The Voltage Isolator provides a barrier between the 5v electronics and the 6v electronics. In Stock - Price: $17.99